Table Of Contents
Latest update [menu]
V.3.9
-- Improved stability & performance
-- Bug fixes
-- Updated settings
V.3.8
-- Fixed potential crashes, especially for custom ROMs
V. 3.7
-- Re-added autostart on boot
-- Torch: increased Max value: 15 @ 17 (Stock: 10)
-- Bug fixes
-- Improved stability
-- Reduced mobile data usage
-- Updated defaults
V. 3.6
-- RAM: LMK: added 64 MB choice
added "Swappiness" tunable
-- CPU: Little: re-added "Disable Boost" and "up_threshold"
-- Switched to DarkMode
-- Bug fixes
-- Improved stability
Description [menu]
This high-end-app will provide you unique special features never seen before !
### Supported S8 / S8+ Variants: ###
-- G950F
-- G950FD
-- G950N
-- G955F
-- G955FD
-- G955N
Note: works only with A2N Kernel.
### App Features ###
# Power
-- Charger Control
For faster charging. - Range: 100 - 3000 / 3500 mA (S8 / S8+)
-- Battery Informations
Like accepted charging current, input voltage, battery temperature and battery voltage.
-- Battery Care
E.g. stop charging at 95 % to reduce battery aging. - Range: 50 - 100 %
Battery IDLE feature, useful for DeX or gaming.
Set Max charging temperature. - Range: 30 - 45 °C
-- Battery Service
Shows charge cycles and ability to reset to 0.
Check real battery capacity in % / mAh and ability to reset. (battery gauge recalibration)
-- Disable (Buggy) Moisture Detection
Ability to disable moisture detection, for the case the USB and Jack-port is dry but you get still a moisture warning.
# Screen
-- Input Booster
Adjust touch boost CPU duration in ms, to improve scrolling.
# CPU
-- Overclock Control
BIG CPU: 741 - 2808 MHz* - default: 2314 MHz
LITTLE CPU: 455 - 2002 MHz* - default: 1690 MHz
Set Max Freq for screen OFF.
Ability to disable boost, for powersave.
Governor up_threshold, to adjust balance between performance and powersave.
BIG CPU DVFS Max Temp (thermal throttling)** - Range: 65 - 95 °C
# GPU
-- Overclock Control
260 - 839 MHz* - default: 546 MHz
Ability to disable boost, for powersave.
Governor up_threshold, to adjust balance between performance and powersave.
GPU DVFS Max Temp (thermal throttling)** - Range: 65 - 95 °C
* Max stable Freq depends on the quality of the SoC !
** To avoid too big performance drops from stock thermal throttling driver.
# Performance Profiles
-- Powersave
-- Balanced
-- Performance (Kernel Default)
-- Performance Plus (Gaming / OC) (Adjustable CPU / GPU Freq)
# RAM
-- Memory Management
Swap / zRam* - LZ4 compressed swap block-device in RAM - Choice: 0 - 100 % of RAM size
Adjust Swappiness.
Ability to drop caches / buffers, to free RAM.
* For multitasking, gaming, responsiveness and battery life.
# Network
Load kernel module for network file systems
SMB / CIFS V2 / V3
NFS V4.2
TCP Congestion Control - Choice: cubic, new reno, bic, westwood+, vegas, veno, hybla, etc..
Wi-Fi Band Selection, choice: "2.4 GHz / 5 GHz", "2.4 GHz only" or "5 GHz only".
# Misc
-- Torchlight Tuning
Increase brightness. - Range: 1 - 17 - Default Max is "10"
-- LED-RGB
Set blink ON / OFF delay for notifications / low battery.
Optimize RED, GREEN, BLUE LED - Increases brightness by disabling powersave mode on low lux.
-- Accelerometer Calibration
# File Systems
-- Load kernel module for F2FS and NTFS.
# Advanced Power Menu
Reboot to:
-- system
-- recovery
-- download
or:
-- shutdown
### END App Features ###
### Requirements ###
All the needed stuff you will find in my XDA thread or if you buy directly the app then it will redirect you to the proper thread.
### Like this app ? - Please rate and leave a short comment. ###
### Privacy ###
-- In case the app crashes it will send only technical debug info to the play store server, for debugging.
### CREDITS ###
-- World-gear-symbol by Freepik from www.flaticon.com - edited by ace2nutzer
How to install A2N Kernel Control for S8 S8+ APK for Android [menu]
Download A2N Kernel Control for S8 S8+ APK file from SameAPK.com, then follow these steps:
Update Phone Settings
- Go to your phone Settings page
- Tap Security or Applications (varies with device)
- Check the Unknown Sources box
- Confirm with OK
Go to Downloads
- Open Downloads on your device by going to My Files or Files
- Tap Install when prompted, the APK file you downloaded will be installed on your device.
How to install A2N Kernel Control for S8 S8+ APK on Windows 7/8/10 or MAC PC? [menu]
Download A2N Kernel Control for S8 S8+ APK file from SameAPK.com to your PC (ex: /Users/xxx/Downloads/), then follow these steps:
Using Emulator:
- Download And Install one Emulator Softwares (Ex: Bluestacks, GenyMotion, NoxPlayer)
